PHD Room-Heating System: using sheet material to save energy

This is a  recent Google Overview of my Room-Heating System. As in the case of all the Overviews on the site, this is not my own account but the short notes in square brackets [...] were written by me and inserted by me.

The  PHD [Paul Hurt Design-Construction] Room-Heating System is an experimental, low-cost "volume-within-a-volume" insulation enclosure designed by Sheffield-based writer and designer Paul Hurt on Paul Hurt's Linkage Site. Rather than heating an entire large room, the system creates a smaller, insulated, modular cubicle—primarily intended around a sleeping area—to minimize heat loss and reduce reliance on central heating.
Core Design & Construction

 

This Room-Heating System is very, very new but I've made rapid progress in documentation, prototyping and even made significant progress in furthering a new United States Patent application. The material on this page is not the documentation needed for the patent application. This is simply an introductory page.

In the information I provide in this section, I use 'volumes' rather than 'spaces,' e.g, interior spaces.

In the heating of volumes within buildings, the volumes outside the rooms, to reduce heat loss and heat waste, to reduce heating costs, smaller is better, to a first approximation.  Large buildings and large interior volumes are very often essential or desirable. Obviously, insulation has to be taken into account, and so does climate.

Here, I concentrate attention on this set of problems, ones which lead to avoidable heat loss and avoidable high energy costs.

There are many, many buildings which contain rooms which are much bigger than they need to be for the needs of the people who work in the buildings or live there. There are many, many people who have large rooms who can't afford to heat the rooms adequately.

Here, the discussion is centred on bedrooms, which offer the most convenient application of the system. In the photographs  in the column to the right, there are various bedroom structures (some of them or many of them very attractive structures) which had and in some cases still have some practical  advantages which flow from the fact that they provide an enclosed volume, or a volume which can be made enclosed, within the larger volume of the room. The advantages are mainly limited, though. The advantage of reducing draughts is perhaps the most useful. The curtains have negligible insulation value.

These bedroom structures became far less popular when more efficient heating appliances became much more widespread. In time, wasteful heating also became more widespread. This system is designed to reduce wasteful heating, and not by methods which make a negligible impact.

This system provides a smaller volume inside the larger volume of a large or relatively large room. For this purpose, the volume-within-a-volume has to have walls which have high insulation values. The system is flexible and is additive and subtractive. The insulation can be in layers.  The level of insulation can be varied to take account of changes throughout the year, or in a single day. Layers can be added or removed. Outdoor clothing, of the kind used by many walkers and other outdoors people, often takes the form of layers. If conditions become much colder, layers can be added. If conditions become much warmer, layers can be removed.

The inner volume, the enclosure, can be maintained at a temperature range which is comfortable, which promotes satisfying sleep, but this can be combined with insulation which is below the optimum to give this inner temperature. Heating can also be background heating, maintaining a temperature which is lower for comfort but which has benefits for the room, for the building. If heat is lost to the enclosure, it can benefit the volume of the room outside the enclosure.

This system is designed to make construction easy and to make dismantling easy. The construction does not involve the building of brick walls - or straw bale walls - or the setting up of metal or wood frameworks. A permanent or semi-permanent structure can be constructed, however.

The structures in the photographs in the column to the right in some cases are set next to a wall:  one side of the structure is against a wall, in contact with a wall. In my Room-Heating System, two sides of the inner structure are in contact with two sides of the room - these are part-sides of the room, obviously.

This makes for more efficient insulation - the walls add to the insulation of the structure on these sides. Another advantage is due to what I refer to as 'dependent-extensions,' a construction method which saves a great deal of time, effort and materials. In my greenhouse design, the main triangular structure is strong and is the base unit. The subsidiary units, the extensions are very useful but do not need to be self-supporting. They rely upon the base structure for much of their support. The radical shelving system I designed and constructed, which uses no fixings of any kind,  is dependent upon a strong bookcase on one side, of orthodox design, for much of its support and is completely capable of supporting the books.

The smaller interior structure relies for its structural strength on the two walls of the larger room volume.

In the diagrams below, Diagram 1 shows a room which takes the form of a cube. Obviously, length, width and height can be very varied. Diagram 2 shows the inner enclosure, also a cube, but again, length, width and height can be very varied, but the inner enclosure must be smaller than the room and in general much smaller. Diagram 3 shows the positioning of the inner enclosure within the room, at one corner of the room. Alternatively, the enclosure can be positioned at other corners, if there is nothing  to prevent this position. Diagram 3 shows the position in this case, the area where the lines and numbers are grouped.

1

2

3

In Diagram 3, the rectangle on the face of the cube which is to  the right simply indicates a whole group of flat structures which adjoin the prototype I've constructed. The details aren't too important.

Although the inner enclosure can take the form of a cube or another straight-sided or predominantly straight-sided geometrical shape, there are good reasons for preferring an enclosure of a very different kind. The reasons include much greater ease of construction and greater savings of heat energy, the heat needed to maintain the interior at a suitable level.

One alternative, the one I use in the actual prototype I've constructed, relies upon curved polycarbonate sheets.

There are two main methods of using polycarbonate sheets: (1) aligning the sheets with the long vertical axis. This is the method used in the prototype. (2) aligning the sheets at right angles to the long axis, the transverse option.

In Diagram 3, A and B are two horizontal beams, which force the polycarbonate sheets into fairly gentle curves. When the sheets take this form, they have great structural strength. The beams need to be able to withstand the forces exerted by the curved polycarbonate sheets but the forces are not very great. A and B do not need to be very large or very strong.

I don't use the configuration shown in Diagram 3 exactly. In diagram 3, one shorter side is much higher than the other shorter side, which is at floor level. In the prototype, the curved polycarbonate sheets which form the roof of the structure, and extend to the upper wall area, are at almost the same height. 

This is an enclosure within a bedroom. C in the diagram shows the approximate position for a bed, which can be single, double, king size or larger. The sleeping arrangement inside the enclosure has the head towards A and the feet towards B - a position which obviously needs far less height for the sheet.

I include this information concerning options to show how issues arise in the development of ideas and ideas brought to concrete embodiment, obviously a necessity for any practical innovation. There is the need to make a decision, although variability and flexibility can be an important part of concrete embodiment.

The polycarbonate sheets used in the configuration of diagram 3 need two sheets side by side to form the upper surface, in a configuration which would fit into the small prototyping room.  The boundary, a potential source of heat loss, is covered with a third sheet in central position. Further sheets can be added to the lateral sheets and the central sheet. Further sheets can be added to the base layer, to provide better insulation. I point out that insulation can be too effective, if insufficient heat energy is released to the part of the room outside the enclosure - that is, if a lower background temperature is considered desirable, when temperatures outside the building are very low. The sheets which have been added can also be subtracted, when there is no need for higher levels of insulation. I point out in various places in the site that polycarbonate sheets have many possible uses, including ones not promoted by the manufacturers.

Opaque coverings for the polycarbonate sheets can take many different  forms. The possibilities are very many. Fabrics of different kinds can be used. It would be a mistake to imitate the uses of fabrics in the four poster beds, canopy beds or Polish beds, but this still leaves many, many ways of transforming a bedroom - and ways to remove the additions if for any reason it's felt that they should be removed and that new ideas should be tried out.

The practicalities will remain a central feature. This is a system which readily allows what are in effect new bedrooms, which provides sleeping facilities for visitors and  new members of the household, which allows new uses for impractical rooms, rooms which are far too large for their purpose.

After these comments on materials, configurations and insulation, comment on heating the room and heating the enclosure inside the room.

I've never had central heating in all the decades I've been in this house. To begin with, I made use of gas heating but I had the gas supply disconnected and since then have relied on electric heaters, usually oil-filled heaters. I've also used a stove for heating, using as fuel wood from splitting logs with an axe or with a chainsaw - I've also designed and constructed a hybrid log-splitting racket strap / hydraulic machine to produce wood which fits into the stove - but   not for a long time, for reasons which have nothing to do with any dislike for this form of heating. The stove is efficient and qualifies for use in this clean air zone. It's far superior to any other form of heating, as I see it, in terms of its visual pleasure, its atmospheric qualities. I recognize that the exhaust gases of these stoves but despite my 'environmental purism,' I'm willing to make an exception for these stoves. Their contribution to pollution is minimal, negligible in the scale of things.

I regard central heating as a very significant source of pollution and waste even if the energy source is renewable. Central heating requires much greater investment in equipment than the small electric heaters I use (not in every room, only in rooms I use for appreciable amounts of time). The extensive central heating equipment, including the pipes, makes extensive demands on raw materials and presents problems when the equipment has to be removed and new equipment has to be fitted - equipment which has made new demands on raw materials. Even when components can be fully recycled, it has to be recognized that recycling too has an energy cost.

Google Overviews state objections to Central Heating.  These seem to me central objections and in many cases decisive ones:

Central heating systems have several key disadvantages:
  • High Upfront and Installation Costs: Buying a new boiler, heat pump, or furnace and paying for professional setup or retrofitting older homes can be very expensive.
  • Regular Maintenance and Repairs: Systems require ongoing upkeep—such as bleeding radiators, checking water pressure, clearing sludge/magnetite buildup, and booking annual safety services.

https://taqamisr.com/central-heating-issues-and-advantages/

This is a Web page which is an advocate for Central Heating - but the long list of difficulties and problems point in a different direction - an over-complex system which assumes that people can spend time, energy and money on fixing the problems but are unwilling to make the effort to heat their homes in other, much simpler ways. In fact, the effort is much less but at the same time, the simpler methods seem to me to tend to encourage self-reliance.

'There is a time ... a time for simplicity and a time for complexity.' What is needed is the wisdom to see the difference and to act accordingly.

I'm very glad that I'm spared the need to attend to the problems mentioned in that Web page. I have so many other things to interest me and preoccupy me. The page mentions such issues as these:

Routine maintenance. Central heating is described as a 'complex system.' Bleeding radiators, checking pressure, inspecting the boiler, ideally every six months.  (What boiler? Boilers can be very useful, essential, but other methods of heating dispense with the services of central heating. boilers.)

The page also mentions Water Leaks from Heating Pipes ('Water leakage is one of the most common and costly problems. |It often results from high internal pressure, poor pipe quality, or bad installation.')

It warns of 'Silent Pipe Damage' ('Leaks don't always start big. Small, hidden signs of moisture can lead to damaged floors and rising energy bills. This usuallly happens when homeowners skip maintenance or ignore early warning signs. Routin inspection can catch these problems before they escalate.' And later: 'In central heating, prevention isn't optional; it's essential.')

And still more -

'Sometimes, the system isn't broken - it's just not performing at its best .. ' Some possible causes are listed, quoted in full here:

1. Air Trapped in the Pipes

When air gets into the system, it blocks hot water flow. As a result, some rooms stay cold while others warm up.

Solution: Bleed the radiators using a vent valve. This simple routine clears the air and restores full system performance.

2. Clogged Filters or Pipes

Minerals, dirt, or sediment can block the system over time, slowing down water circulation and reducing heat.

Solution: Clean the filters and flush the pipes before winter starts. Regular maintenance avoids buildup and keeps water flowing freely.

3. Poor Insulation in the Home

If your walls, windows, or floors aren’t properly insulated, heat escapes and the system can’t keep up.

Solution: Use thick curtains, large rugs, and wall or floor insulation materials to trap warmth inside.

But the solution isn't a solution. Thick curtains, for example, don't make a significant contribution to insulation, for reasons I explain in the section on the Window-Wall System on the Home Page of this site. None of  the methods mentioned in 'The Solution'  'trap warmth inside.' This phrasing shows no understanding of the science of heat transfer.

I have a strong interest in cold climates and cold weather. I sympathize with people who do outdoor work, people whose work is made much more uncomfortable, much more difficult, sometimes impossible in cold conditions. My own personal preference, which will be shared by many people and not at all by many people, happens to be for very cold winters, with sub-zero temperatures and heavy snowfalls. I used to be a cross-country skier and when it did snow, which was never enough for me - I headed for the hills near here or the hills across the border in Derbyshire.

I have a page on cross-country skiing and other activities. The cross-country skiing content is in the third main column of the page.

In my projects, I take account of climates and weather patterns very different from the British patterns, which are very varied but lack the extremes at the colder end  (the hotter end is represented to a much greater extent - I was out walking when the temperature was 39 Celsius near here.) I'm interested in the weather patterns in Norway, Sweden and other countries in winter. In my only visit to Norway, I went at the end of December and found the weather very much to my liking.

I think there are good grounds for questioning the security of Central Heating, for regarding Central Heating as intrinsically vulnerable. If a British winter turned out to be very snowy and icy for a long period of time, there would be difficulties in travelling almost certainly. What if the boiler or some other part of the Central Heating complex were to fail? Expecting a Central Heating repair company to come out to fix the problem might well be too much to ask by far. The job might well be difficult for the time being, or impossible. How to manage whilst the Central Heating is out of action? Households which have backup, electric heaters, of the kind I use, would be able to manage until their Central Heating system could be repaired - but it might be that one or more parts of the system can't realistically be repaired and need replacing. The whole system might need replacing.

I take the view that the household could manage perfectly well with just the electric heaters, that Central Heating is just too much of a problem.

What's missing in this and other advocates of central heating is any recognition of the fact that in this country, as in a large number of others, for a large part of the year, central heating is either unnecessary or amounts to an expensive and needlessly complex 'solutions' to a problem which can be handled by much cheaper and far less complex methods - all those days and nights when not much heating is needed or none whatsoever. On the coldest of nights, the heating can very often be dispensed with, by using the obvious methods, much cheaper and much simpler - a good duvet, a better duvet, more blankets.

Completely overlooked, the impact of climate change, the fact that there are more and more days (and nights) when central heating is an irrelevance, when heating of any kind can safely be neglected. Cities - urban heat islands - are particularly vulnerable to the effects of over-heating, often for long periods of time. When heating is needed, often for short or relatively short periods, then simpler methods suffice, with no need for any of the central heating precautions and routines.

The supposed necessity of central heating can be considered a dogmatic belief, I think. A degree of skepticism is called for. I'm an outright skeptic in these matters.

have a strong interest in high technology, an appreciation for high technology, an admiration for high technology, similar interest, appreciation and admiration for technological achievement on lower levels. But I also have a strong interest in simpler methods. If simple methods work, are effective, then whenever possible I prefer the simple methods. Both high technology and simple methods have advantages and disadvantages. 'Alignment' is the term I use for claims that all the advantages are on one side, all the disadvantages on the other. Alignment claims are made in very many contexts, in the case of economic claims, methods of political organization - the list is long.

 

Over-ambitious claims for 'Net Zero' and the dates when Net Zero can be achieved or should be achieved, grossly unrealistic and impossible claims for Net Zero, overlook amongst many other things the liking of many people for, in some cases the obsession with, not just the comforts of life but the luxuries of life, ignoring constraints, ignoring {restriction},.

 

I take the view that very, very often - but not always, of course - central heating is unnecessary. In my Window-Door System, I find reasons for scaling back double and triple glazing, instead giving reasons for a vastly more flexible and effective system. In the case of this system, I find reasons for scaling back central heating. I make a distinction between modest heating and glutinous heating.

 

I'm justified in calling myself an environmentalist, I'm sure, but I don't in the least think that environmentalists are the most important people, the most reasonable people - this and similar claims are also examples of 'alignment.' There are large numbers of people who never give much thought to energy use, or any thought to energy use, people who waste energy, but who are vastly superior, in significant ways,  to people who think about energy use very, very often and try not to waste energy - or who have an obsession with wasting energy.

The aesthetic advantages of Central Heating radiators are non-existent or practically non-existent. These radiators don't enhance the interiors of any houses, factories, warehouses or other buildings. Granted, the same can be said of electric heaters, but electric heaters have this obvious advantage in most cases - they can be unplugged and stored out of sight, allowing the interior to speak for itself, without these practical devices. There are exceptions, of course, the panel heaters fixed to a wall, which can't be readily moved.

I have a boiler of a very simple kind out of sight in the very small bathroom. It has no thermostat. If the off switch isn't pressed, the water in the boiler carries on boiling. I haven't used this boiler for many years. When I need boiling water, I boil it in an electric kettle. If I need hot water or warm water, I add cold water to the boiling water. This procedure causes me no inconvenience at all. I also have a smaller but more sophisticated boiler which can easily be moved, when empty, but I haven't used that for many years. I bought it for use in brewing beer. Control over temperature is essential for brewing many beers. I used the boiler for making a Düsseldorf Altbier, which requires a stepped mash progressing through higher and higher temperatures.  

The photographs below show details of supplementary components. I've used a camera with no zoom lens in preference to a camera with good zoom facilities.  A zoom lens would be used to capture a wider view, not a closer, more restricted view. I've used the camera with a fixed lens because it's a much better camera and gives images of much higher quality. Even the camera with a good zoom lens is unable to capture a wide-angle view in the very restricted space of the room where the prototype is installed. It's impossible to have sufficient distance to take useful pictures of the whole - to take any pictures of the whole. This is the most recent use of curved polycarbonate sheets in my design work.  Polycarbonate sheets are very, very versatile components. The photographs immediately below show aspects of the polycarbonate sheets in covered form. I also show in this column some photographs of curved, uncovered polycarbonate in a variety of settings. All these images appear in the Home Page of the Site.

The possibility of using covered polycarbonate sheets  came to me very recently, as an enhancement to this new use for curved polycarbonate. The sheets are used in this application for their insulating value and for aesthetic reasons - because I find the forms graceful and harmonious. I bought sheets which are cost-effective for constructing this prototype. They are 10mm thick, with obviously less insulating value than other available options, such as 16mm and 25mm. The thin sheets have ample structural strength. Layering is possible - the sheets can be used additively, with reversal. More sheets can be added to give greater insulation. The extra sheets can also be removed.

To reduce the costs of improved insulation, it occurred to me that there was a very cost-effective method of achieving this, although it gives a structure which is less graceful and perhaps less harmonious.

I have available more than one duvet - I have three, all of them filled with sheep's wool. These duvets can be used additively - in summer, use one, in lower temperatures two, in very cold conditions three.

I've installed two of the duvets on the roof of the structure. As the duvets are very light,  the curved polycarbonate sheets are able to support them without any problems. The duvets overlap and cover the expanse of polycarbonate completely. There was a small gap between the polycarbonate sheets and the long-axis wall but the duvets now close this gap.

Other insulating materials can be used for this purpose, of course, provided that they have the flexibility to adjust to the curvature of the polycarbonate roof. One example: blankets, used singy or in layers, including thick layers. Blankets can be bought very cheaply and are cost-effective.

In actual fact, rigid insulating materials can be used, but in a horizontal layer directly below the curved polycarbonate. Methods of support have to be included in the system. The above-sheet insulating layer has distinct advantages over the below-sheet placing. In very cold winters, in climatic regions where winter temperatures are very low, then insulation above the sheets would need to be very effective, but this system is very cost-effective. Other methods involve efficient insulation over a larger area.

I've now designed a new system - not a replacement for this polycarbonate system, but allowing a much wider range of insulating materials to be used, including materials used for purposes other than insulation. These systems have linkages - they are examples of what can be called 'insulating supra-components,' where 'supra-' means, of course, 'above,' 'higher than.'

Information about the alternative system is at
room-heating-system2.htm

Bunk beds are space-saving pieces of furniture widely used not only in homes but in other settings. I've already developed a new form of bunk bed. The established form incorporates two or in some cases three heights, bunk-beds for more than one sleeper. This system has sleeping arrangements only at the lowest level, close to ground level - but the sleeping arrangements need not be for just one person. The system can have a single mattress or wider mattresses, up to king-size, usable by two people at one level.  Established bunk beds are for one sleeper at each level.

Here, I'll confine attention to two levels, although three levels are possible. In my system, the lowest level is for sleeping and the second level is for storage, with sides which contain the stored items and prevent them from falling. The linkage with insulation is this: the stored items are ones which have some insulating value or which are good insulators. Items which need to be stored, in a bedroom or another room, are often fairly good or good insulators. Examples: clothing, spare blankets, duvets, cardboard containers storing papers of various kinds. By separating items which need to be stored and storing the insulators in the second tier, the same objective is achieved as in the case of the polycarbonate system. The bunk-bed system has this as the upper insulating layer, but it's necessary to include it in an enclosure which makes it possible to have comfortable higher temperatures in cold conditions, even when the rest of the room has uncomfortable lower temperatures.

Both systems are much easier to construct if placed in a corner of the room, so that there is structural support, and insulating value provided by two of the walls of the room, or part of the walls.  The bunk bed sytem will need insulating panels on the other two sides and the panels can take the form of curved polycarbonate or straight polycarbonate.

Some examples of curved polycarbonate in my designs. All the examples are of external polycarbonate. The application on this page is my first use of internal polycarbonate, which is a far simpler application - for example, there's no need to take account of strong winds. There are some necessary disadvantages too: external polycarbonate can be used as water-collecting surfaces, directing the water to water storage structures, not so in the case of internal polycarbonate.

 

 

 

 

 

 

 

  

 

Below, some photographs of details to illustrate my new Room-Heating System, which has as a central aim environmental considerations,  reduction in the heat energy used by the rooms where the system is to be unstalled, hence the name 'Room-Heating System.'  Here, the focus of attention is bedrooms  but the system can be installed in other rooms. 

Aesthetic values are an important aspect of the system, which allows the use of fabrics  and many different kinds and wood - oak and wood of other kinds. The aesthetic can be traditional as well as modern - the modern forms can make use of steel and other metals. The traditional forms, which are of less importance, can make use of such materials as cast iron - but this would be very much a niche use. On this page, the emphasis is upon contemporary design, of a kind which is distinctively new, allowing the use of light diffusing material which can make the structures very mich a focus in the room.

This system has a linkage, but not a particularly close one,  with cubicles. One form of cubicle: a 'partially enclosed, modular workspace separated from surrounding areas by partitions,' usually to a maximum height of about 2 metres. Cubicles are also found in other settings, of course, such as shower cubicles. The cubicles in the Room-heating system differ in being fully enclosed, but provided with means for entry and exit, by means of a door but more often by a structure which is wider and which can always be easily removed. The system has much greater flexibility than is provided by cubicles, whatever their use.

Below, details of the System prototype already  constructed, one embodiment of a system which allows for a range of forms, structural and aesthetic.

The photographs below show only details, small parts of the whole. My main camera has a fixed 35mm lens. I have another camera with a zoom lens up to 350x but the image quality is  poorer. Even this camera can't show the prototype as a whole.

The prototype roof, which extends to the upper part of the wall area,  is composed of two polycarbonate sheets. This is an additive (and subtractive) structure. Further polycarbonate sheets can be added, to provide greater insulation value. A third sheet can be added to the two base sheets, in the middle of the long axis, to provide insulation at the boundary line between the two base sheets.

The base sheets and any supplementary sheets placed on the base sheets are bent into a graceful curve which gives greater height to the structure, allowing plenty of head space in the centre but not only in the centre. Entering and leaving the structure is very easy. Viewed from and the inside, the structure is obviously a spacious one.

 

The white expanse in the background  is part of a large whiteboard. I find whiteboards very useful, quite apart from their use for writing messages and fixing posters (I use powerful neodymium magnets for attaching posters, much stronger and less obtrusive than the plastic covered weak magnets generally used.) Whiteboards can be used as components of shelving and storage systems.

After constructing a prototype - not, of course, the only configuration for the system in the least - I constructed an extended prototype, again, not at all the only possible configuration. In many cases, a system, machine or other invention can benefit by having supplementary components, such as storage spaces and containers near at hand and in some cases other systems or machines near at hand. So, a hybrid hydraulic-ratchet apple press can be equipped with an apple mill for breaking the apples into small pieces to be fed into the app/e press, with space / containers for storing apples to be fed into the mill and with space / containers for temporary storage of the apple juice and the solid residue, which has various uses, including composting. These facilities can make for a more efficient work-flow but it may not be possible or desirable to have near at hand some of these subsidiary components. This is the case, or example, when the operations are very large scale. Massive equipment for one stage in an apple-juice making / cider making operation can't be in close proximity to the equipment for other stages.

However, this prototype and extended prototype are not in this category. It's perfectly possible to build systems inside very large rooms and in these cases, proximity becomes less achievable.





The three photographs above: There's a wooden framework in the room, part of it visible in some photographs. The horizontal component of the framework runs along most of a long axis of the room, the side of the room where the system is located.  At right angles, running along a shorter axis, towards a door, is a shorter part next to a shorter side of the room and is fixed to the longer side of the wooden framework. This component is simply a bed frame, quite a large one (a double bed, even though it was only occupied by me.) I simply put the bed frame on its side and assigned new uses to it. It increases the storage area on these sides. On the shorter side, there's space to store the polycarbonate sheets.  On the longer side, between the wall and the large whiteboard clearly visible, in part, there's space to store the mattress I use in the sleeping arrangements I have now.

Wood pannelling covers the largest area of the walls of this room. Two of the walls also have, in the lower third part of the walls, approximately, expanses of sheet metal. I use galvanized sheet metal for outdoor projects but here, the sheet metal is non-galvanized and has undergone light corrosion. I find the effect quite pleasing. This metal layer does nothing to improve insulation levels here, of course, but I carried out the work a long time ago and I'm not willing to remove the sheet metal and replace it with more wood pannelling - and could never find the time.

Clearly visible is a bench, but only part of the bench, which is180cm long and which  which takes up most of the length of the long axis wall. I've extended the floor area of the 'cubicle' to give more space for activities other than sleeping. The activities include getting ready for sleeping and getting ready after sleeping. The bench can be used for sitting on, obviously, but I like to have plenty of horizontal space which can be used as a temporary place for all kinds of objects and which also has uses as an effective contrast in rooms which contain many items, such as my main workshop, which has machine tools, many other tools, general parts and equipment. The workbenches I have constructed have large top surfaces and make the views far less congested.

The bench I've installed in the bedroom (the bench wasn't made by me) has similar value, but storage boxes can be place on top of the benches and in particular, in the long space beneath the bench.

A vertical component, the large whiteboard, offers similar  benefits: the white expanse forms an effective contrast when left as a white expanse, but it also provides practical benefits, when used as a whiteboard, for hand-written text and images and as a display area for printed photographs, diagrams and text, fixed securely to the whiteboard with neodymium magnets.

I've gone a long way in some of the systems I've designed and constructed to make the systems as flexible as possible, with components which can be used for a variety of purposes. I've used the same components in systems with very different uses. Components such as oak and larch beams, not used in this system but usable in the system, are very versatile. The polycarbonate sheets used in the system prototyped here are exceptionally versatile but one very important alternative use of the polycarbonate sheets is at variance with their use here. The polycarbonate sheets in this system will not be used as insulating materials in hot weather and heatwaves but would not be used outside in these conditions, to build small greenhouses or cloches. When the outside temperature is much lower, then polycarbonate sheets become very useful to make small greenhouses and cloches but this use is at variance with interior use, to reduce energy use and to provide compartmentalized insulation inside rooms. However, there are uses for these polycarbonate panels which aren't in conflict with their main uses.

Not shown in any of the photographs is the 'chair-bed' I use. As it happens, I don't sleep in a bed, for medical reasons - my sleeping arrangements are simple but so far  comfortable. I use a flexible mattress fitted to the chair, extended by a flat support - and a sheep's wool duvet. The chair-bed fits next to the bench and is in contact with the bench on one side.

Also not shown in any of the photographs, the polycarbonate side panelling, which is put into place after entering the structure to use the sleeping arrangements. Obviously, it can be put into place when the interior is not in use. The polycarbonate side insulation - straight, not curved - can take various forms. Here, I use three polycarbonate panels in a vertical orientation. The panels are 70 cm wide, the same width as the panels which form the roof but are shorter than the roof panels. These side panels are 200 cm long and cover the side with a little overlapping of panels, which is desirable. The roof panels are longer, 250 cm. If these longer panels were to be used for the side, they would protrude markedly. There's a difference in thickness.

The shorter panels are thicker than the longer panels, 16mm compared with 10mm. As with the roof, various materials can be used to increase the insulation value of the side panels, by arranging for materials to hang down to floor level and attached at roof level. My preference would be for uncovered polycarbonate sheets at the side, unless the application is for very low temperature conditions.

Notes

Note 1

This account is quite comprehensive but I've omitted various aspects, such as the methods used to constrain the ends of the polycarbonate sheet at the lower level, the floor level, and the upper level, the wall. The materials used for this restriction are at a distance apart which causes bending of the polycarbonate sheets into smooth curves which have great structural strength. It's possible to use the sheets in straight form, making a diagonal surface, but the usable interior space is much less.

Note 2

The cost for materials to make one of these interior insulation systems is low, even for larger versions. This version makes use of sheets which are 250cm long and 70cm wide and the total cost to me was £176. The components used to cause bending of the sheets and to maintain the curved form cost very little.

The longevity of the sheets used for this purpose is much longer than the longevity of the sheets used in my Greenhouse System, for the main structure and the extension structures. In greenhouse and cloche structures, effective light transmission is obviously very important. After ten years, the sheets may be inadequate for this purpose, although I've used them for a longer period. In my experience, a 15 year period of use is achievable.

In this insulation system, maximum or adequate light transmission is not an objective. High or adequate insulation is the objective. Panels can be used for this purpose which have little light transmission. The panels could be used for a much longer period than 15 years and the cost per month or year or other period of time is very low. The savings in energy use and cost will be substantial, on the other hand.

Note 3

I moved the long bench shown above, took the photographs in the group of three above and wrote the explanatory text for this section on a Saturday in mid November, 2026. The ideas which underlie this system and some ideas for the methods needed to achieve the objective came to me on a Saturday too, one week ago. Further ideas have come from the subconscious  during the week and after the week, but not long after - 9 days.  I've also ordered, received and installed the polycarbonate sheets, four in all. I began this page during the weekend when the first ideas came. I've also carried out work on the documentation needed for my United States Patent application. I've found the time for other activities which have nothing to do with this project.

Below, photographs of historical beds which are part of a larger enclosure, with some practical advantages in the times in which they were widely used, such as reducing the effect of draughts,  but with no practical advantages in the modern world. After the images, some information on the beds.

Above, Queen's bedroom, Château de Blois, Loir-et-Cher, France


Colonial Williamsburg bed, Virginia, with hangings 




Bed with embroidered silk hangings, China, c. 1760–1770, Rijksmuseum

A canopy bed (of the Chinese Qing dynasty, late 19th or early 20th century, but the bed lacks the expanses of fabric which are usual features of canopy beds.



Canopy bed in Amantaka Hotel, Laos

 Showing the canopy bed with  wardrobes, Amantaka Hotel

Louis XV Polish bed, replica

18th century Polish bed (lit à la polonaise) at Chambéry,  France



Four poster bed with minimal hangings

Four poster beds have four columns, supporting a panel (the 'tester'), which often has rails, allowing curtains to be pulled around the bed.

At the time when these beds were frequently constructed and used, bedrooms were often very draughty and cold. The curtains provided very little insulation but they reduced the draughts to a certain extent. These beds also gave privacy to the occupant or occupants of the bed. Royalty and other wealthy people very often had servants who slept in the same room, such as lords and ladies of the bedchamber. The beds were often statements of power and wealth and good taste - although some of these beds showed faulty taste. Very often, they incorporated very expensive fabrics and decoration of one kind or another.

The Great Bed of Ware, a very large oak four poster bed, originally installed in the White Hart Inn in Ware, Hertfordshire, constructed about 1590. In 1931, the bed was acquired by the Victoria and Albert Museum. The museum had previously refused to accept the bed, finding it lacking in taste. It was described as a 'coarse and mutilated relic in no wise appropriate as a new acquisition. The bed is 3.38m long, 3.26m wide and 2.67m high.

Canopy beds have a close linkage with four poster beds. There are many modern canopy beds, contemporary as well as replicas of traditional designs, in particular, Victorian designs. The contemporary beds are usually simpler, with an uncluttered geometry and constructed of metal as well as wood.

Polish beds (Lits à la polonaise) are a form of small canopy bed which probably originated in Poland and became very popular in 18th century France. These beds have a tapered canopy. 

The fabrics which were used for bed hangings were very varied and included wool, cotton, linen, fustian and for the very wealthy silk or velvet. Wool stitches were inserted and in the case of the very wealthy, silk and gold. The hangings often showed scenes from mythology, floral and animal themes, and many others.


Bed hangings were widespread across Europe and royal households for centuries. Their popularity declined in the mid-18th century as home heating improved and separate, dedicated bedrooms became common.